FSI DAT3060S 3 line, 3 or 4 stage Mass Casualty Decon Shower System. Perform Decon for 3 to 6 ambulatory, 3 non-ambulatory, or any combination. Undress/Detergent Shower/Rinse Shower/Redress configuration.
The FSI DAT®3060S is a three-line wide (4', 5', 4' –1.2 M, 1.5 M, 1.2 M), 3 or 4 -station Mass Casualty Decon Shower System which handles three parallel lines of casualties at the same time in three or four sequential stations --- (1) undress, (2) detergent shower # 1 - (3) rinse shower # 2 OR handle 2 personnel in separate showers simultaneously in each lane, (4) redress. This unit deploys in under two minutes, and processes up to six ambulatory persons at a time or 3 non-ambulatory persons on stretchers simultaneously – or any combination. Undress and redress stations are dry (plumbing is possible and optional); Four (4) shower stations include 3 showerheads and one hanging coiled ½”/13 mm hose line with attached multiple function spray nozzle which thoroughly drenches and decontaminates via a fine water mist.The two (2) middle line shower stations include two hanging coiled ½”/13 mm hose lines with attached multiple function spray nozzles.There are a total of 20 water discharge ports as standard.Shutoffs and quick disconnects supplied with every group of shower heads and trigger gun.As an option -- by configuring the changing areas on both ends as decon showers one can double the capacity as detailed above.If an optional detergent injector is used then the shower # 1 station can be used for detergent cleansing and the shower # 2 station may be used for rinse. Wastewater is contained within integral 13’ W (3.96 M) X 12’ L (3.65 M) ground floor and 6”/15 cm berm erected when system is initially inflated (holds 300 gallons/1200 litres of waste water before pump-out is required). Includes 3 separate “dirty” entry and “clean” full sized exit man doors on each end, 9 (nine) 1/3rd cross divider curtains, 2 (two) center divider curtains to separate the 3 lines, two windows per side, 2 skylights, 2 – ¾” (19 mm) High pressure 300 psi(20 bar) GHT threaded inlet hoses – other fittings available as specified, reflective air vents at each end, reflective striping on each end to delineate built in decon pool.All canopy walls are velcro’d to the floor air berms for air lock.These professional decon systems can be inflated either with high pressure air from an scba/ scuba tank, with an electric inflator, or with compressed air from any available source.The DAT3060S offers a top center air berm running the entire length of the unit at the roof line and secondary full center length air berms running on either side of the main center berm approx. 18 - 24" off center. FSI offers a total of five 8” - 12" diameter lateral roof support air berms - size of shelter dependent.FSI shelters lead the industry in terms of weight/snow bearing capabilities/strength.Whatever the specification at hand FSI meets and exceeds herein.
Weight approx. 335 pounds/152 Kg.Inflated size inside to inside is 13’ W (3.96 M) x 20’ L (6.1 M) x 9’ H (2.74 M).For outside to outside dimensions add 16” in Width and Length = 14.33 Ft.WX21.33 Ft. L = 306 sq ft approx.Carton size approx. = 136 X 108 X 91 cm (54” L X 43” W X 36” H)All units come equipped as standard equipment with an integral ground floor, 2 roll up windows per side, 2 skylights, roll-up, full zip, dirty entry/clean exit doors, 4 HVAC 19”/48 cm air duct inlets/outlets w. tie closures – 2 per side (may also be used as clothes discharge outlets), 2 high pressure and 2 low pressure inflation deflation valves, one air inflation hose w. safety cord, 2 pressure relief valves, 10 stainless steel stakes and ground anchor points, Repair kit, manual, shelter sleeve, 2 upper air vents, and hammer.Unit supplied w. no charge redundant features allowing for - hanging undress/redress kits etc. on the inlet and outlet side.Units can attach to a second shelter/shower system.1100 dtex material is 1.5mm thick and consists of 0.62mm plastomer coated PVC/0.3mm polyester yarn/0.62mm plastomer coated PVC**All FSI Portable Hazmat Decon Shower Systems are in conformance with the performance requirements of the new ANSI/ISEA # 113-200X American National Standard for Fixed and Portable Decontamination Shower Units.
Frame:Heavy Duty 1100 Dtex* polyester coated w. plastomer on both sides, UV/Chemicalresistant.Canopy:Heavy duty 100% nylon twill (3/5) w. PU white pigment inner coating, ABT. 0 23mm X 57/58.Wt. AB1.230GR/Sq. M - UV/chemical resistant/fire retardant – UV resistant and water repellent w. a hydrostatic resistance of 250 psi +-Mildew resistant to meet and exceed US Fed. Test MIL.STD.810E 508 - Fire resistance meets and exceeds CPAI 84 SECTION 5 1995, US Fed. Test CFR.1610, meets NFPA701 Flammability Test method 1 (2004), NFPA 702 w. ‘A’ burn scale rating.Floor:PVC of 0.58mm thickness (1,000 Dtex, 18 X 18 polyester) 660 grams per sq. mm60” W.Standard color is ‘EMS’ Blue.Green and White also available as standard.Other colors offered P.O.A.Technical data:Air pressure internally once inflated = 4.3 psi (0.3 bar)USA Federal Standard FS # 191 5041/5102/5134/5970 Test Method Structural Test resultsTotal Weight (g/m2) – 1055Thickness (mm) – 0.90Cut strip tensile strength (lbs. /in.) – Warp = 450-Weft = 404Elongation (%) – Warp = 30- Weft = 47Tongue tear (lbs.) – Warp = 87 – Weft = 100Adhesion (lbs. /in.) – Warp = 9.4 – Weft = 8.9Density = 30 X 24.5Multiple optional accessories available inclusive of air and water heaters, air coolers, elevation grids, waste water pumps, etc. available .
Hazmat Decon Shower Shelters 
