FSI DATAL Aluminum Framed Series Decon Shower - L 1.83 m x W 2.43m x H 2.5 m H (6 ft L X 8 ft W  X 8.25 ft H) 48 sq ft approx. 119 lbs., packed dim. 40" X 40" X 47" 7 spray nozzle heads one multifunction Trigger gun.


FSI DATAL Aluminum Framed Series Decon Shower - L 1.83 m x W 2.43m x H 2.5 m H (6 ft  L X 8 ft W  X 8.25 ft H)   48 sq ft  approx. 119 lbs., packed dim. 40" X 40" X 47"   7 spray nozzle heads one multifunction Trigger gun.  First Responder Portable Haz mat Decon shower system.   See DAT2020S for comparable pneumatic model


Name File size    
decon_manual_2016 5.92 MB

Technical Specs







Canopy:   Heavy duty 100% nylon twill (3/5) w. PU white pigment inner coating, ABT. 0 23mm X 57/58. Wt. AB1.230GR/Sq. M - UV/chemical resistant/fire retardant – UV resistant and water repellent w. a hydrostatic resistance of 250 psi + - Mildew resistant to meet and exceed US Fed. Test MIL.STD.810E 508 - Fire resistance meets and exceeds CPAI 84 SECTION 5 1995, US Fed. Test CFR.1610, meets NFPA701 Flammability Test method 1 (2004), NFPA 702 w. ‘A’ burn scale rating.

Inner canopy: If applicable - of 100% NYLON 210T ANTRON W/R, POLYURETHANE COATED 57/58", Color: White - Flame Retardant to meet 'NFPA-701 TM-1', Anti-fungus/Anti-mildew, opaque

Floor: 1,000 denier Nylon coated w. PU, tensile strength: 2545N/2360, Tear Strength: 106/102N, weight: 490 g/yd.

Frame/Hub: DAT® AL Series™ Frame/Hub Material Specifications:

Patent pending retractable, corrosion resistant, 16mm HD aluminum tubing with 1.5mm wall thickness tubing shelter w. high density polyfiber hub. Length per section = 73cm (29”). Minimum tear strength of 215 Mpa (31,200 psi). Complete with welded 650 g/sqm double fabric at the frame/canopy connector points for maximum product strength at all critical locations.

Approx. 55 mph wind resistance; approx. roof load 2,200 lbs. – 20 + lbs/sq ft.





DAT® AL SERIES™ ‘Quick Erect’ General Set up and Tear down Instructions:

All parts are pre-assembled with no special tools required. Frame system is made of interconnected aluminum tubes that fold out in a scissor type movement.

To ‘Quick Erect’- place the floor cover in the designated area and then place the closed/folded up DAT® AL™ series unit in the center of the floor cover.  With 2-4 support personnel (size of unit dependent) have personnel grip each corner.  Pull the width support frames slowly until unit is fully open and fits floor cover exactly. Then from underneath - lift the center of the tent upwards until the two sides reach the ground almost perpendicular to one another. Clip the buckles together at the four corners (inside of the frame) while supporting the center of the tent in the air.  Check/final position canopy and affix floor with HD velcro attachments.  Commence use.

Standard color is a blue color designated as FSI Blue® exterior w. high visibility white inside color. Green, White, and Tan/Sand exterior canopy color also available at no extra cost. Other colors available P.O.A.



Multiple optional accessories available inclusive of air and water heaters, air coolers, elevation grids, waste water pumps, etc. available


The DAT®AL48S comes equipped as standard equipment with an attachable ground floor and decon pool that will hold up to 100 gallons (400 liters) of water (with an 8”/20 cm berm approx.) before requiring pump out, 2 roll up windows – one on each side, 1 skylight, full closure slip in and out dirty entry/clean exit doors on each end, 4 metal stakes and ground anchor points, one 19”/48 cm HVAC Hanging Duct, 1 small electrical duct, Tie Down Ropes and 4 D-rings to tie off to, Repair kit, manual, shelter sleeve, 2 upper air vents, and hammer. All canopy walls are velcro’d to the floor, and reflective striping is found on the upper air vents above doors and on entry and exit air berms. Units can attach to a 2nd shower/FSI Shelter.

The DAT®AL48S also comes complete with a qty. of 7 spray nozzle heads (one overhead) and a single 5’ (150 cm) length of coiled ½”/13 mm hose with an attached multiple function spray gun with spray patterns and flows meant to gently yet thoroughly drench and decon victims. Shutoffs and quick disconnects supplied with every group of shower heads and trigger gun. Flows per shower head and per spray gun = approx. 1 gpm/4 lpm optimum and dependent on water volumes available. 

Simply ‘quick erect’ the unit and plug into a water supply. The DAT®AL48S offered with 1 – ¾” (19mm) high pressure 300 psi (20 bar) GHT threaded inlet hose – other fittings available as specified. Decontamination can commence in less than 1 minute.


Comes complete with stakes, and repair kit

Unit supplied w. no charge redundant features allowing for - hanging undress/redress kits etc. on the inlet and outlet side and - doubling of showering capability in the future.


**All FSI Portable Hazmat Decon Shower Systems are in conformance with the performance requirements of the new ANSI # 113 American National Standard for Fixed and Portable Decontamination Shower Units.





©Copyright 2011. All rights reserved. FSI® FSI North America®, Fire Safety International, Inc.®
DAT®, The color BLUE  which FSI designates as
  FSI Blue®,  FSI Holdings, LLC®, DAT®'QE Series'®, Transporter® and DAT®AL Series™ are all registered trademarks of FSI®.   All rights will be protected.