DAT6120SS

PDFPrint
DAT6120SS-water1.jpg

FSI DECON SHOWER SHELTER SYSTEM -a complete outer canopy and removable decon pool, removable shower fixtures and curtain lines allowing this same system to be converted into a 262 sq ft. command or other use shelter system in minutes. As a shower - ins

Description

FSI DECON SHOWER SHELTER SYSTEM -a complete outer canopy and removable decon pool, removable shower fixtures and curtain lines allowing this same system to be converted into a 262 sq ft. command or other use shelter system in minutes. As a shower - install decon pool and shower heads and curtains in approx. 5 minutes and have a 3 line 3 or 4 stage Mass Casualty Decon Shower System that can decon 3 to 6 ambulatory, 3 non-ambulatory, or any combination. Undress/Detergent Shower/Rinse Shower/Redress configuration. 5ft L undress area/ 5ft L detergent shower area/5ft L rinse shower area/ 5ft L redress area. As a shelter simply remove decon pool/shower heads/shower curtains as desired in approx. 5 minutes and have a complete 262 sq ft shelter system complete with outer canopy and inner insulating canopy that is ready for use. Approx. 13ft W X 20ft L x 9ft H, 260 sq. ft., 395 lbs.

 

FSI® DAT® SERIES PNEUMATIC SHELTER SYSTEMS

 

GENERAL SPECIFICATIONS

020509mc

Air pressure internally once inflated = 4.3 psi (0.3 bar)

USA Federal Standard FS # 191 5041/5102/5134/5970 Test method structural test results

Total Weight (g/m2) – 1055                            Thickness (mm) – 0.90

Cut strip tensile strength (lbs. /in.) – Warp = 450 - Weft = 404

Elongation (%) – Warp = 30 - Weft = 47                 Tongue tear (lbs.) – Warp = 87 – Weft = 100

Adhesion (lbs. /in.) – Warp = 9.4 – Weft = 8.9                            Density = 30 X 24.5

 

Frame: Heavy Duty 1100 Dtex* polyester coated w. plastomer on both sides, UV/Chemical resistant, quadruple overlapped and glued.

Canopy:   Heavy duty 100% nylon twill (3/5) w. PU white pigment inner coating, ABT. 0 23mm X 57/58. Wt. AB1.230GR/Sq. M - UV/chemical resistant/fire retardant – UV resistant and water repellent w. a hydrostatic resistance of 250 psi + - Mildew resistant to meet and exceed US Fed. Test MIL.STD.810E 508 - Fire resistance meets and exceeds CPAI 84 SECTION 5 1995, US Fed. Test CFR.1610, meets NFPA701 Flammability Test method 1 (2004), NFPA 702 w. ‘A’ burn scale rating. All seams double stitched and coated both sides.

Inner canopy: If applicable - of 100% NYLON 210T ANTRON W/R, POLYURETHANE COATED 57/58", Color: White - Flame Retardant to meet 'NFPA-701 TM-1', Anti-fungus/Anti-mildew, opaque

Floor: PVC of 0.58mm thickness (1,000 Dtex, 18 X 18 polyester) 660 grams per sq. mm 60” W.  

 

Standard color is ‘FSI Blue’ TM exterior w. high visibility white inside color. Green and White exterior canopy color also available as standard. Other colors optional P.O.A..

 

FSI® DAT® SERIES PNEUMATIC SHELTERS

 

All Shelters have full privacy zipper closure and full screen zipper closure slip in and out dirty entry/clean exit doors, 2 high pressure* and 2 low pressure inflation deflation valves*, 2 pressure relief valves*, one air inflation hose w. safety cord, tie down ropes and 4 D-rings to tie off to, repair kit, manual, shelter sleeve, 2 upper air vents, and a hammer.   All canopy walls are velcro’d to the floor air berms for air lock, and reflective striping is found on the upper air vents above entry and exit doors.   Units can attach to a second FSI shelter or shower. Simply inflate the unit and commence use in approx. 1 - 4 minutes (size of shelter dependent). DAT3030/DAT3015 have one only high pressure, one only low pressure inflation deflation valve, one only pressure relief valve

 

Every shelter with a width of over 11 ft - regardless of length and overall size offers a top center air berm running the entire length of the unit at the roof line and secondary full center length air berms running on either side of the main center berm approx. 18 - 24" off center.  FSI offers a total of five 8” - 12" diameter lateral roof support air berms - size of shelter dependent. FSI shelters lead the industry in terms of weight/snow bearing capabilities/strength. Whatever the specification at hand FSI meets and exceeds herein.

 

Every FSI® DAT® series shelter comes complete with electric inflator/deflator, and high pressure compressed air fill hose and universal high pressure scba fitting.

 

All units supplied w. no charge redundant features allowing for - hanging undress/redress kits etc. on the inlet and outlet side.

 

All DAT® series shelters available with cross and center divider curtains, side doors, extra windows, skylights, HVAC/clothing ducts with ties, etc. as per published FSI literature/pricing/specs.

 

Multiple optional accessories available inclusive of air heaters, air coolers, elevation grids, waste water pumps, etc. available.

 

Files:
Name File size    
decon_manual_2016 5.92 MB